FloJet

FloJet

Pumps

Flojet pumps 12 volt & 240 volt Pressure pumps

Spare Parts

Spare Parts and Accessories for Flojet Pumps


Display per page
Sort by

12v Pump & Motor remote controller

12v Pump & DC motor Speed control kit.

Allows the control of the speed of the 12v electric motor  and 12v pump equipment. designed to operate with 12v pumps and motors up to 15A maximum this unit has many applications in 12v spraying, illiminate pump on/off cycling allowing the pump deliver the exact volume required to operate the spray nozzle or boom evenly without nozzle fluctuation which can lead to failure to apply accurately.

The plug and play design of this Controller makes simple what is otherwise difficult to acheive giving in-cab remote control of not just pump on off but also effectively pressure control via pumping speed/volume control.

What's included; 

  • Control switch box with Fuse & adjustable mounting bracket
  • 12v Battery Supply power cable
  • 4m Controller to pump wiring loom with terminal block connector
  • Operation instruct booklet

 

$220.35 *
In stock, ships within 24 hours

5D Quick Connect 12v pump suction filter

Quick Connect 12v pump suction filter

Suction filters increases longevity of your 12v pump and components by reducing unnecessary premature wear and blockages.

Large screen area, the screen is reinforced against collapsing as can occur, its easily serviced and will assist in ensuring better productivity and longer pump life.

For use on Flojet*, Delavan*, Silvan Smoothflo*, Seaflo*, Northstar & Stanley 12v pumps

Connects straight to the pump inlet and is fitted with a 5D 19mm (3/4") quick connect mount

Filter screen is 50 mesh, its also easily removed for service.
Suits all 5D 19mm (3/4") quick connect pumps.
The larger size filter screen means longer service intervals.
The filter housing can be rotated to 360° to allow you to best position the suction hose

* some models

$24.90 *
In stock, ships within 24 hours
Delivery weight: 0.22 kg

12v Pump Pressure Regulator -5D Pump Quick connect

Regulator for 12v Pump with Female nut connection to pump

Generate a smooth constant flow with your 12 volt pump rather than stop start fluctuaion.
Ideal for boom spraying applications.
Suitable for pumps up to 20L/min flow
Suits many brands of pumps including Delavan*, Flojet*, Stanley, Northstar, Silvan Aquatec*, Seaflo* etc
Not sure if it fits your pump get in contact with us to find out
 

Features;

  • Polypropylene body reinforced with fibreglass
  • 1/8” (BSP) for pressure gauge connection (gauge not included)
  • EPDM seals
  • Internal parts in DELRIN and stainless steel AISI 303 for long life
  • Regulating graduated indicator

* various models

$53.97 *
In stock, ships within 24 hours
Delivery weight: 300 g

3D Quick Connect 12v pump suction filter

Quick Connect 12v pump suction filter

Suction filters increases longevity of your 12v pump and components by reducing unnecessary premature wear and blockages.

Large screen area, the screen is reinforced against collapsing as can occur, its easily serviced and will assist in ensuring better productivity and longer pump life.

For use on Flojet*, Delavan*, Seaflo* and other 3D quick connect 12v pumps. 

Filter screen is 50 mesh, its also easily removed for service.

Connects straight to the pump inlet and is fitted with a 3D 16mm (5/8") quick connect mount

Suits all 3D 16mm (5/8") quick connect pumps.
The larger size filter screen means longer service intervals.
The filter housing can be rotated to 360° to allow you to best position the suction hose

* some models

$24.90 *
In stock, ships within 24 hours
Delivery weight: 0.22 kg

Flojet 3501-506 8L/min 60psi 12v pump

Flojet 3501-506

FLOJET Industrial Triplex Low Pressure Series pumps are designed for a wide range of applications and are constructed from a selection of materials suitable for handling a broad range of chemicals. The Triplex Low Pressure diaphragm pumps are selfpriming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. The higher the duty cycle,the shorter the expected life of the pump. Typical pump uses are liquid transfer, spraying, cooling, circulation, filtration and dispensing.

• Compact automatic demand pump
• Sealed pressure switch and motor
• Self-priming, pump can be located above supply tank
• Can run dry for extended periods of time without damage
• Flow rates to 2.0 GPM (7.6 l/min) and operating pressure to 50 psi (3.4 bar)

• Fitted with 4 Bar (60 PSI) Pressure Switch
• Internal bypass for smooth running even at low flows
• Viton valves, Santonprene diaphragm

3501-506

Flow Rate                          7.8 lpm  (open flow)
Motor                                   Permanent magnet TENV (non-ventilated)
Pump Design                    Three Chamber
Voltage                                12 Vdc
Amp Draw                            8 amp
Pressure Switch Setting    2.0-4.1 bar 30-60 psi
Max. Operating Pressure   3.4 bar 50 psi
Max. Fluid Temperature      54 °C 130 °F
Self Priming                          Up  to 2.4m vertical height
Port(s)                                    3/8” NPTF
Wetted Parts                          Housing – Reinforced Polypropylene
Elastomers                            Santoprene®, Viton®
Weight                                    1.5 kg
$216.56 *
Ships within 24 hours
Delivery weight: 1.8 kg

12v Pump Pressure Regulator & Gauge - 5D QC mount

Regulator for 12v Pump with 5D QC mount

Generate a smooth constant flow with your 12 volt pump rather than stop start fluctuaion.
Ideal for boom spraying applications.
Suitable for pumps u[ to 20L/min flow
Ideal for Flojet, Silvan Smoothflo, Delavan, Northstar, Seaflo, Stanley and other Brands 12 v Pumps with 5D 19mm (3/4" quick mount)
Not sure if it fits your pump get in contact with us to find out
 

Features;

  • Polypropylene body reinforced with fibreglass
  • 1/8” (BSP) for pressure gauge connection
  • Liquid filled Pressure gauge
  • EPDM seals
  • Internal parts in DELRIN and stainless steel AISI 303 for long life
  • Regulating graduated indicator

* various models

**5D mount measure 19mm (3/4") Diameter

$88.25 *
In stock, ships within 24 hours
Delivery weight: 500 g

5D (3/4") - Quick release 12v pump fittings various shape s & sizes

5D (3/4" / 19mm) QC. to Straight and elbow barbs & 1/2" threads

Selection of both 10mm (3/8"),13mm (1/2") & 19mm (3/4") hose barbs  along with threaded 1/2" Bsp male threads.

Suit many models & brands with QC (snap in) pump connections including DELEVAN, FLOJET, STANLEY, NORTHSTAR, AQUATEC SMOOTHFLO, SEAFLO.

Details;

Pump Connection 5D (measures 19mm or 3/4")
Hose connection 10mm (3/8"), 13mm (1/2") & 19mm (3/4")
Thread connection 1/2"
Fitting shape Straight & Elbow

If you are uncertain if these can fit your pump send us an email.

$8.45 *
Ships within 24 hours
Delivery weight: 0.1 kg

Flojet 3501-503 8L/min 60psi 12v pump

Flojet 3501-503

FLOJET Industrial Triplex Low Pressure Series 12v pumps are designed for a wide range of applications and are constructed from a selection of materials suitable for handling a broad range of chemicals. The Triplex Low Pressure diaphragm pumps are selfpriming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. The higher the duty cycle,the shorter the expected life of the pump. Typical pump uses are liquid transfer, spraying, cooling, circulation, filtration and dispensing.

• Compact automatic demand pump
• Sealed pressure switch and motor
• Self-priming, pump can be located above supply tank
• Can run dry for extended periods of time without damage
• Flow rates to 2.0 GPM (7.6 l/min) and operating pressure to 50 psi (3.4 bar)
• Fitted with 4 Bar (60 PSI) Pressure Switch
• Internal bypass for smooth running even at low flows
• On/off rocker switch on pump body
• Viton valves, Santonprene diaphragm

3501-506

Flow Rate                          7.8 lpm
Motor                                 Permanent magnet TENV (non-ventilated)
Pump Design                    Three Chamber
Voltage                                12 Vdc
Amp Draw                            8 amp
Pressure Switch Setting    2.0-4.1 bar 30-60 psi
Max. Operating Pressure   3.4 bar 50 psi
Max. Fluid Temperature      54 °C 130 °F
Self Priming                          Up  to 2.4m vertical height
Port(s)                                    3/8” NPTF
Wetted Parts                          Housing – Reinforced Polypropylene
Elastomers                            Santoprene®, Viton®
Weight                                    1.5 kg
$259.88 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 3251-139 15.1L/min 60psi 12v pump

Flojet 3521-139

FLOJET 3521 Series Triplex Low Pressure Series pumps (15.1 LPM open flow) are designed for a wide range of applications and are constructed from a selection of materials suitable for handling a broad range of chemicals.

The 3521-139 Triplex pump is suitable for a number of applications including running small Spray Booms.  The internal bypass fitted to this model makes it a very flexible pump suitable for a wide range of applications from spot spraying to a small boom (up to 6 m). Triplex Low Pressure diaphragm pumps are selfpriming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. The higher the duty cycle,the shorter the expected life of the pump. Typical pump uses are liquid transfer, spraying, cooling, circulation, filtration and dispensing.

• Compact automatic demand pump
• Sealed pressure switch and motor
• Self-priming, pump can be located above supply tank
• Can run dry for extended periods of time without damage
• Flow rates to 15.1 and operating pressure to 50 psi (3.4 bar)
• Fitted with 4 Bar (60 PSI) Pressure Switch
• Internal bypass for smooth running even at low flows
• Viton valves, Santonprene diaphragm

3521-500

Flow Rate                          15  lpm  (open flow)
Motor                                   Permanent magnet TENV (non-ventilated)
Pump Design                    Three Chamber
Voltage                                12 Vdc
Amp Draw                            8 amp
Pressure Switch Setting    2.0-4.1 bar 30-60 psi
Max. Operating Pressure   3.4 bar 50 psi
Max. Fluid Temperature      54 °C 130 °F
Self Priming                          Up  to 2.4m vertical height
Port(s)                                    Plug in Flojet fitting
Wetted Parts                          Housing – Reinforced Polypropylene
Elastomers                            Santoprene®, Viton®
Weight                                    1.5 kg
$280.91 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 4300-142 14L/min 45psi 12v pump

Flojet 4300-142

The Flojet 4300-142 has an open flow rate of 14 LPM and is fitted with EPDM checkvalves and santoprene diaphragms. Suitable for operating boomless spray nozzles and small spray booms up to 4m wide with yellow nozzles.

The Flojet 4300-142 series is a self-priming pump. It is fitted with a pressure switch to provide “on demandspraying and cut out.

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

Features

Self-primes up to 2.4m vertical lift
• Handles Water-Like and Viscous Liquids up to 250 cP
• Four-piston design delivers higher & smoother flow rates
Chemical-resistant polypropylene pump head for Iong life
5D Quick-Connect plug-in ports for easy installation
• In built pressure-switch control to run the pump only as needed

$290.81 *
In stock, ships within 24 hours
Delivery weight: 3.5 kg

12v Pump Wiring Loom

Wiring loom for 12v pumps

Takes the effort out of making up a wiring connection for your 12v pump. Easy plug & play setup.

Supplied with;

  • battery clamps
  • inline on/off switch
  • 2m dual core wire
$34.00 *
In stock, ships within 24 hours
Delivery weight: 350 g

FloJet 2135-568 6.5L/min 75 psi 12v Pump

Flojet 2135-568

This unit was standard equipment on early Croplands ATV spray units.

  • Maximum Flow is 6.4 LPM (Open Flow)
  • Maximum Pressure is 6 bar  (75 psi) cut-out pressure,
  • Power input is 12v DC,
  • Diaphragms are Buna,
  • Check Valves are Viton,
  • Pump Body is Polypropylene,
  • Connections are 1/4″ female BSP threads,
  • Maximum liquid temperature is 54 degrees C.

 

Flojet 6.4 LPM 12VDC 75 PSI self priming diaphragm demand water pump.

Constructed with polypropylene housing, viton check valves & Buna diaphragm to handle a broad range of agricultural and chemicals products plus many other applications

  • In built  pressure switch automatically starts and stops the pump when the discharge valve opens and closes.
  • Ball bearing drive throughout the pump and motor assures longer pump life,
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry for short periods of time without damage,
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications,
  • Heavy duty ball bearing drive system
$309.38 *
Ships within 24 hours
Delivery weight: 2.9 kg

Flojet 4100-505 14L/min 45psi 12v pump

Flojet 4100-505

Flojet 4100 series pumps are suitable for a wide range of agricultural and industrial applications. The 4100-505 is common fitment on Hardi 12 volt spray equipment.

The Flojet 4100-505 has an open flow rate of 14 LPM and is fitted with Viton check valves and santoprene diaphragms.
The Flojet 4100 series is a self-priming pump.
ideal for use with pressure relief valve.
It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

For vertical pump mounting be sure that the motor is located on top. This will prevent water from entering the motor chamber in event of a leak.

4100-505
  • Compact design and plug-in port fitting make installation easy.
  • Can run dry without damage and handle liquids up to 54° C.
  • No metal contact with liquid being pumped.
  • Ball bearing drive throughout pump and motor assures longer pump life.
  • Excellent self-priming capability. Pump may be located above the liquid level.
  • Powerful, permanent magnet motor with low current draw and long life brushes.
$310.00 *
In stock, ships within 24 hours
Delivery weight: 2.5 kg

Flojet 4300-143 18L/min 45psi 12v pump

Flojet 4300-143

The Flojet 4300-143 has an open flow rate of 18 LPM and is fitted with EPDM checkvalves and santoprene diaphragms. Suitable for operating boomless spray nozzles and spray booms up to 6m wide with yellow nozzles.

The Flojet 4300-143 series is a self-priming 12v pump. It is fitted with a pressure switch to provide “on demandspraying and cut out.

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

Features

• Self-primes up to 2.4m vertical lift
• Four-piston design delivers higher & smoother flow rates
Chemical-resistant polypropylene pump head for Iong life
5D Quick-connect plug-in ports for easy installation
• In built pressure-switch control to run the pump only as needed

$311.52 *
In stock, ships within 24 hours
Delivery weight: 3.5 kg

Flojet 2100-777 6L/min 60 psi 12 v pump

Flojet 2100-777

Flojet 8 LPM 12VDC 60 PSI self priming diaphragm demand water pump. Constructed with polypropylene housing, viton check valves & santoprene diaphragm to handle a broad range of agricultural and chemicals products plus many other applications

  • In built  pressure switch automatically starts and stops the pump when the discharge valve opens and closes.
  • Ball bearing drive throughout the pump and motor assures longer pump life,
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry for short periods of time without damage,
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications,
  • Heavy duty ball bearing drive system

2100-777

Maximum Flow is 8 LPM (Open Flow)
Maximum Pressure is 420 kPa (60 psi) cut-out pressure,
Power input is 12v DC,
Diaphragms are Santoprene,
Check Valves are Viton,
Pump Body is Polypropylene,
Connections are 3/8″ female BSP threads,
Maximum liquid temperature is 54 degrees C.

$315.56 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 2100-122 8L/min 60psi 12 v pump

Flojet 2100-122

Flojet 8 LPM 12VDC 60 PSI self priming diaphragm demand water pump. Constructed with polypropylene housing, viton check valves & diaphragm to handle a broad range of agricultural and chemicals products plus many other applications

  • In built pressure switch automatically starts and stops the pump when the discharge valve opens and closes.
  • Ball bearing drive throughout the pump and motor assures longer pump life,
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry for short periods of time without damage,
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications,
  • Heavy duty ball bearing drive system
2100-122

Maximum Flow is 8 LPM (Open Flow)
Maximum Pressure is 420 kPa (60 psi) cut-out pressure,
Power input is 12v DC,
Diaphragms are Viton,
Check Valves are Viton,
Pump Body is Polypropylene,
Connections are 3/8″ female BSP threads,
Maximum liquid temperature is 54 degrees C.

$334.13 *
Ships within 24 hours
Delivery weight: 2.5 kg

Flojet 4100-143 18L/min 45psi 12v pump

Flojet 4100-143

Flojet 4100 series pumps are suitable for a wide range of agricultural and industrial applications. With flow rates to 18 LPM and pressure to 45 PSI the 4100 series pump range is suitable for boom spraying as well as application and transfer of many chemicals.

The Flojet 4100-143 has an open flow rate of 18 LPM and is fitted with EPDM checkvalves and santoprene diaphragms.
The Flojet 4100 series is a self-priming pump.
The Flojet 4100-143 is not fitted with a pressure switch.
Ideal to use with pressure relief valve.

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

For vertical pump mounting be sure that the motor is located on top. This will prevent water from entering the motor chamber in event of a leak.

Features

  • Compact design and plug-in port fitting make installation easy.
  • Can run dry without damage and handle liquids up to 54° C.
  • No metal contact with liquid being pumped.
  • Ball bearing drive throughout pump and motor assures longer pump life.
  • Excellent self-priming capability. Pump may be located above the liquid level.
  • Powerful, permanent magnet motor with low current draw and long life brushes.
$334.13 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 3251-500 15.1L/min 60psi 12v pump

Flojet 3521-500

FLOJET 3521 Series Triplex Low Pressure Series pumps (15.1 LPM open flow) are designed for a wide range of applications and are constructed from a selection of materials suitable for handling a broad range of chemicals.

The 3521-500 Triplex pump are suitable for a number of applications including running small boom sprays.  The internal bypass fitted to this model makes it a very flexible pump suitable for a wide range of applications from spot spraying to a small boom (up to 6 m). Triplex Low Pressure diaphragm pumps are selfpriming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. The higher the duty cycle,the shorter the expected life of the pump. Typical pump uses are liquid transfer, spraying, cooling, circulation, filtration and dispensing.

• Compact automatic demand pump
• Sealed pressure switch and motor
• Self-priming, pump can be located above supply tank
• Can run dry for extended periods of time without damage
• Flow rates to 15.1 and operating pressure to 50 psi (3.4 bar)
• Fitted with 4 Bar (60 PSI) Pressure Switch
• Internal bypass for smooth running even at low flows
• Viton valves, Santonprene diaphragm

3521-500

Flow Rate                          15.1  lpm  (open flow)
Motor                                   Permanent magnet TENV (non-ventilated)
Pump Design                    Three Chamber
Voltage                                12 Vdc
Amp Draw                            8 amp
Pressure Switch Setting    2.0-4.1 bar 30-60 psi
Max. Operating Pressure   3.4 bar 50 psi
Max. Fluid Temperature      54 °C 130 °F
Self Priming                          Up  to 2.4m vertical height
Port(s)                                    Plug in Flojet fitting
Wetted Parts                          Housing – Reinforced Polypropylene
Elastomers                            Santoprene®, Viton®
Weight                                    1.5 kg
$336.60 *
In stock, ships within 24 hours
Delivery weight: 2.5 kg

FloJet 2100-232 6L/min 60 psi 240V Pump

Flojet 2100 series, diaphragm pump.

Suitable Uses - Continuous duty as a medium volume water supply for carpet cleaning machines. 
Suitable liquids - Many chemicals, sea water, fresh water, sugars, whisky and wine etc.
Warranty - 12 months National Warranty Aust wide.

Materials used -

  • Pump Head: Polypropylene   
  • Diaphragms: Santoprene   
  • Valves: Santoprene

Electrical -

  • Voltage: 230v AC   
  • Amp draw: 0.25A   
  • Watts: 57W   
  • Power lead length: 40cm

Pressure switch - Cut out pressure: 60 PSI (4.1 bar)

Self prime - Up to 2.4m maximum. Self-priming.

Liquid Temperature - 54°C Maximum

Inlet/Outlet Ports - 3/8" Female NPT thread


It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump.)
For vertical pump mounting be sure that the motor is located on top.
Pump head may be rotated in 90° increments to simplify plumbing.
Built-in pressure switch automatically starts and stops pump instantaneously when discharge valve is opened and closed.

  • Can run dry without damage and handle liquids up to 54°C.
  • Duplex Diaphragm Design eliminates troublesome shaft seal.
  • No metal contact with liquid being pumped.
  • Ball bearing drive throughout pump and motor assures longer pump life.
  • Excellent self-priming capability. Pump may be located above the liquid level.
  • Powerful, permanent magnet motor with low current draw and long life brushes.

This pump is supplied as a spare part and must be installed by a licensed electrican or service person.

$337.84 *
Ships within 24 hours
Delivery weight: 2.9 kg

Flojet 2100-734 8L/min 50psi 12 v pump

Flojet 2100-734

Flojet 8 LPM 12VDC 50 PSI self priming diaphragm liquid pump. Constructed with polyprolylene housing, viton check valves & diaphragm to handle a broad range of agricultural chemical products plus many other applications

  • Ball bearing drive throughout the pump and motor assures longer pump life,
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry without damage,
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications,
  • Heavy duty ball bearing drive system

Features

Designed for use with pressure relief valve
Maximum Flow is 8 LPM (Open Flow)
Maximum Pressure is 50 PSI,
Power input is 12v DC, Motor Fan cooled for harsh conditions
Diaphragms are Viton,
Check Valves are Viton,
Pump Body is Polypropylene,
Connections are 3/8″ female BSP threads,
Maximum liquid temperature is 54 degrees C.
$340.31 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 4100-113 18L/min 45psi 12v pump

Flojet 4100-113

Flojet 4100 series pumps are suitable for a wide range of agricultural and industrial applications. With flow rates to 18 LPM and pressure to 45 PSI the 4100 series pump range is suitable for boom spraying as well as application and transfer of many chemicals.

The Flojet 4100-113 has an open flow rate of 18 LPM and is fitted with Buna checkvalves and geolast diaphragms.
The Flojet 4100 series is a self-priming pump.
The flojet 4100-113 is not fitted with a pressure switch.
Ideal for use with a pressure relief valve

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

Features

  • Compact design and plug-in port fitting make installation easy.
  • Can run dry without damage and handle liquids up to 54° C.
  • No metal contact with liquid being pumped.
  • Ball bearing drive throughout pump and motor assures longer pump life.
  • Excellent self-priming capability. Pump may be located above the liquid level.
  • Powerful, permanent magnet motor with low current draw and long life brushes.
$344.03 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 2130-132A 6.8Lmin 95 psi 12 v pump

Flojet 2130-132

Flojet 6.8 LPM 12VDC 95 PSI self priming diaphragm demand water pump. Constructed with polypropylene housing, EDPM check valves & diaphragm to handle a broad range of agricultural and chemicals products plus many other applications

  • In built  pressure switch automatically starts and stops the pump when the discharge valve opens and closes.
  • Ball bearing drive throughout the pump and motor assures longer pump life,
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry for short periods of time without damage,
  • Fan cooled motor for improved running in tough conditions
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications
  • 1/4 female ports
  • Heavy duty ball bearing drive system

Features

Maximum Flow is 6.8 LPM (Open Flow)
Maximum Pressure is 6.5 bar (95 psi) cut-out pressure,
Power input is 12v DC, Motor fitted with fan,
Diaphragms are EDPM,
Check Valves are EDPM
Pump Body is Polypropylene,
Connections are 1/4″ female BSP threads,
Maximum liquid temperature is 54 degrees C.

$370.00 *
Ships within 24 hours
Delivery weight: 2.4 kg

Flojet 4300-506 18L/min 45psi 12v pump

Flojet 4300-506

Flojet 4300 series pumps are suitable for a wide range of agricultural and industrial applications. With flow rates to 18 LPM and pressure to 45 PSI the 4300 series pump range is suitable for farm boom spraying as well as application and transfer of many chemicals.

The Flojet 4300-143 has an open flow rate of 18 LPM and is fitted with Geolast checkvalves and Buna diaphragms. These materials are compatable with diesel.

The Flojet 4300 series is a self-priming pump. It is fitted with a pressure switch to provide “on demand” spraying and cut out.

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

For vertical pump mounting be sure that the motor is located on top. This will prevent water from entering the motor chamber in event of a leak.

4300-506

• Self-primes up to 2.4m vertical lift
• Handles Water and Viscous Liquids up to 250 cP
• Four-piston design delivers higher flow rates
• Chemical-resistant polypropylene pump head for Iong life
• Choice of elastomeric materials to work with many chemicals
• Quick-connect plug-in ports for easy installation
• In built pressure-switch control to run the pump only as needed

$370.01 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 2100-848 8L/min 60 psi 12 v pump

Flojet 2100-848

Flojet Open flow Duplex Pump 8 LPM 12VDC 50 PSI self priming diaphragm liquid pump. Constructed with polyprolylene housing, viton check valves & santoprene diaphragm to handle a broad range of agricultural chemical products plus many other applications

  • Ball bearing drive throughout the pump and motor assures longer pump life, Fan cooled motor for tough environments
  • Self-priming up to 2.4m so the pump can be located above the supply tank,
  • Can run dry without damage,
  • Built-in thermal protection,
  • Low Amp draw for battery powered applications,
  • Heavy duty ball bearing drive system

Features

Designed to be used with pressure relief valve
Maximum Flow is 8 LPM (Open Flow)
Maximum Pressure is 50 PSI,
Power input is 12v DC, Motor Fan cooled for harsh conditions
Diaphragms are Viton,
Check Valves are Santoprene
Pump Body is Polypropylene,
Connections are 3/8″ female BSP threads,
Maximum liquid temperature is 54 degrees C.
$320.00 *
Ships within 24 hours
Delivery weight: 1.8 kg

Flojet 4300-504 18L/min 45psi 12v pump

Flojet 4300-504

Flojet 4300 series pumps are suitable for a wide range of agricultural and industrial applications. With flow rates to 18 LPM and pressure to 45 PSI the 4300 series pump range is suitable for agricultural boom spraying as well as application and transfer of many chemicals.

The Flojet 4300-143 has an open flow rate of 18 LPM and is fitted with Viton checkvalves and santoprene diaphragms.

The Flojet 4300 series is a self-priming pump. It is fitted with a pressure switch to provide “on demand” spraying and cut out.

It may be located several feet from the tank, above or below the liquid level (it is not a submersible pump).

For vertical pump mounting be sure that the motor is located on top. This will prevent water from entering the motor chamber in event of a leak.

4300-504

• Self-primes up to 2.4m vertical lift
• Handles Water-Like and Viscous Liquids up to 250 cP
• Four-piston design delivers higher flow rates
• Chemical-resistant polypropylene pump head for Iong life
• Choice of elastomeric materials to work with many chemicals
• Quick-connect plug-in ports for easy installation
• In built pressure-switch control to run the pump only as needed

$393.53 *
Ships within 24 hours
Delivery weight: 1.8 kg
*
Prices incl. GST, plus delivery